Practice on 2023 LATEST API-570 Exam Updated 150 Questions
Download Latest API-570 Dumps with Authentic Real Exam QA's
NEW QUESTION 67
An operator notice a pipe off its support, what should be done?
- A. Contact maintenance personnel for immediate repair
- B. Report the situation to engineering or inspection personnel
- C. Keep a record of the situation for future reference
- D. Ignore the situation
Answer: B
NEW QUESTION 68
Is the thickness range on the WPS supported by the PQR?
- A. No
- B. Re qualification is required by API 570
- C. Re qualification is required by ASME Section V
- D. Yes
Answer: A
NEW QUESTION 69
Who has the responsibility for qualifying welding procedures?
- A. Each contractor
- B. Each subcontractor
- C. Each employer
- D. Each welder
Answer: C
NEW QUESTION 70
The preheat zone shall extend beyond each edge of a pipe weld
- A. 3T
- B. 2"
- C. 2T
- D. 1"
Answer: D
NEW QUESTION 71
The repair organization shall maintain records of welding procedures and welder qualifications and make the records available to the inspector_____.
- A. after completion of welding
- B. when the repair organization releases the information
- C. prior to the start of welding
- D. any time during welding
Answer: C
NEW QUESTION 72
Appropriate permanent and progressive records on each piping system shall include.
- A. system service; classification; identification numbers
- B. all jurisdictional requirements
- C. original heat and batch numbers
- D. all original construction data
Answer: A
NEW QUESTION 73
Excessive cyclic stresses that are well below the static yield strength of the material result in.
- A. material failure
- B. fatigue cracking
- C. failure cracking
- D. creep cracking
Answer: B
NEW QUESTION 74
API 570 covers the inspection of__________.
- A. In-service piping
- B. new construction
- C. In-service vessels
- D. new tank construction
Answer: A
NEW QUESTION 75
Is the attached PQR properly qualified?
- A. No, because peening is allowed by ASME B31.3
- B. No, because there are not enough tensile tests
- C. Yes
- D. No, because RT is not allowed during PQR qualification
Answer: B
NEW QUESTION 76
provides general requirements and detailed assessment procedures for specific types of degradation that are referenced in API 570.
- A. ASME 816.5
- B. API 598
- C. API 653
- D. API RP 579
Answer: D
NEW QUESTION 77
What is the pressure design thickness of NPS10A516 Gr.65 Type 22 pipe that operateat 1200psig/750°F
- A. Not enough in formation given
- B. 0.928"
- C. 0.432"
- D. 0.46"
Answer: D
NEW QUESTION 78
The liquid penetrant examination method is an effective means for detecting.
- A. surface discontinuities of a weld
- B. internal discontinuities of a weld
- C. subsurface discontinuities of a weld
- D. both Internal and surface discontinuities of a weld
Answer: A
NEW QUESTION 79
Penetrameters are normally placed on the side of the part being examined.
- A. film
- B. source
- C. reverse
- D. weld
Answer: B
NEW QUESTION 80
Without the benefit of an impact test, what is the minimum operating temperature for A-106 Grade B material used in a Category D Fluid Service?
- A. -20°C
- B. -29°F
- C. -20°F
- D. 0°F
Answer: C
NEW QUESTION 81
Welding procedures qualified by may be used, subject to the specific approval of the inspector
- A. others
- B. the use of API 1104 qualified procedures
- C. the use of AWS pre qualified, D1.1 type procedures
- D. the employer
Answer: A
NEW QUESTION 82
can cause flame detectors used to indicate a furnace or boiler fire to give false indications on control panels.
- A. Radiographic inspection
- B. Piping alterations in the shop
- C. Welding or related repairs on piping
- D. Ultrasonic inspection
Answer: A
NEW QUESTION 83
Geometric unsharpness of the radiograph of a component under 2" th1ck shall not exceed
- A. 0.050"
- B. 0.040"
- C. 0.020"
- D. 0.030"
Answer: C
NEW QUESTION 84
A visual examination of performance test coupons shall_______.
- A. show complete joint penetration and complete fusion of weld metal and base metal
- B. be allowed one 5/32" crater crack
- C. show no more than 1/3t non fusion
- D. show no more than 1/3t inadequate penetration
Answer: A
NEW QUESTION 85
More than one contractor, manufacturer or installer may simultaneously qualify a welder. In such case, each participating organization shall be represented by during the test.
- A. A certified welding inspector
- B. A welding engineer
- C. A responsible employee
- D. The welder's supervisor
Answer: C
NEW QUESTION 86
In a piping circuit, which of the following does not routinely have thickness measurements taken?
- A. Fittings
- B. Dead legs
- C. Valves
- D. Straight Run Pipe
Answer: C
NEW QUESTION 87
Besides ultrasonic instruments, what other method can be used to determine thickness measurements?
- A. ET
- B. AET
- C. RT
- D. MT
Answer: C
NEW QUESTION 88
......
Authentic API-570 Exam Dumps PDF - Apr-2023 Updated: https://vceplus.practicevce.com/API/API-570-practice-exam-dumps.html